Toyota Tacoma (2015-2018) Service Manual: Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body or Combination Meter / Data List.
(e) According to the display on the Techstream, read the "Data List".
Main Body|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
ACC SW |
Ignition switch ACC signal / ON or OFF |
ON: Ignition switch ACC OFF: Ignition switch off |
"ON" is also displayed for this item when the ignition switch is ON. |
|
IG SW |
Ignition switch ON signal / ON or OFF |
ON: Ignition switch on OFF: Ignition switch off |
"OFF" is also displayed for this item when the ignition switch is ACC. |
|
Parking Brake SW |
Parking brake switch signal / ON or OFF |
ON: Parking brake switch on OFF: Parking brake switch off |
- |
|
Auto High Beam Main Switch |
Auto high beam switch signal / OFF or ON |
OFF: Auto high beam switch off ON: Auto high beam switch on |
w/ Automatic High Beam System |
|
RR Door Courtesy SW |
Rear door courtesy light switch assembly RH signal / ON or OFF |
ON: Rear door RH open OFF: Rear door RH closed |
- |
|
RL Door Courtesy SW |
Rear door courtesy light switch assembly LH signal / ON or OFF |
ON: Rear door LH open OFF: Rear door LH closed |
- |
|
Cargo Light Switch |
Deck light switch signal / ON or OFF |
ON: Deck light switch on OFF: Deck light switch off |
- |
|
FR Door Lock Pos |
Front door RH unlock detection switch signal / ON or OFF |
LOCK: Front door RH locked UNLOCK: Front door RH unlocked |
- |
|
FR Door Courtesy SW |
Front door courtesy light switch assembly RH signal / ON or OFF |
ON: Front door RH open OFF: Front door RH closed |
- |
|
FL Door Lock Pos |
Front door LH unlock detection switch signal / LOCK or UNLOCK |
LOCK: Front door LH locked UNLOCK: Front door LH unlocked |
- |
|
FL Door Courtesy SW |
Front door courtesy light switch assembly LH signal / ON or OFF |
ON: Front door LH open OFF: Front door LH closed |
- |
|
RR-Door Lock Pos SW |
Rear door RH unlock detection switch signal / LOCK or UNLOCK |
ON: Rear door RH unlocked OFF: Rear door RH locked |
- |
|
RL-Door Lock Pos SW |
Rear door LH unlock detection switch signal / ON or OFF |
ON: Rear door LH unlocked OFF: Rear door LH locked |
- |
|
Dimmer SW |
Dimmer switch high position signal / ON or OFF |
ON: Dimmer switch in high or high flash position OFF: Dimmer switch not in high flash position |
- |
|
Passing Light SW |
Dimmer switch high flash position (pass) signal / ON or OFF |
ON: Dimmer switch in high flash position OFF: Dimmer switch not in high flash position |
- |
|
Front Fog Light SW |
Fog light switch front position signal / ON or OFF |
ON: Fog light switch in front position OFF: Fog light switch off |
w/ Fog Light |
|
Auto Light SW |
Light control switch AUTO position signal / ON or OFF |
ON: Light control switch in AUTO position OFF: Light control switch not in AUTO position |
w/ Automatic High Beam System |
|
Head Light SW (Head) |
Light control switch head position signal / ON or OFF |
ON: Light control switch in head position OFF: Light control switch not in head position |
- |
|
Head Light SW (Tail) |
Light control switch tail position signal / ON or OFF |
ON: Light control switch in tail or head position OFF: Light control switch in neither tail nor head position |
- |
|
Light Sensor Illuminance |
Light control sensor illuminance / 0 to 8191 lx |
Value is output according to ambient light level |
- |
|
Interior Light Control |
Operation of the illuminated entry system / OFF or ON |
Customized value is displayed |
Displayed only when All Data is selected. |
|
I/L ON W/Door Key Unlock |
Function that lights up the interior lights when the doors are unlocked / OFF or ON |
Customized value is displayed |
Displayed only when All Data is selected. |
|
Lighting Time |
Lighting time of the delay control function (illuminated entry system) / 15 s, 7.5 s or 30 s |
Customized value is displayed |
Displayed only when All Data is selected. |
|
Room Light when Aprchd |
Function that lights up the interior lights when a key enters any actuation area*1 / OFF or ON |
Customized value is displayed |
Displayed only when All Data is selected. |
|
I/L when ACC OFF |
Function that lights up the interior lights when the ignition switch is turned from ON or ACC to off / OFF or ON |
Customized value is displayed |
Displayed only when All Data is selected. |
|
Sensitivity |
Sensitivity of the automatic light control system / Light2, Light1, Normal, Dark1 or Dark2 |
Customized value is displayed |
- |
|
DRL Function |
DRL function / ON or OFF |
Customized value is displayed |
*2 |
|
Disp Ex ON Sen |
Ambient brightness level required to dim display lights (combination meter, navigation display, etc.) / Light2, Light1, Normal, Dark1 or Dark2 |
Customized value is displayed |
- |
|
Disp Ex OFF Sen |
Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.) / Light2, Light1, Normal, Dark1 or Dark2 |
Customized value is displayed |
- |
|
Light Auto OFF Delay |
Light auto OFF delay / Off, 30 s, 60 s, or 90 s |
Customized value is displayed |
*2 |
|
Auto H Beam STS0 |
Automatic high beam sensor state past 0 / Undetec, CAM NA, Nosens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err |
Condition can be displayed*3 |
- |
|
Auto H Beam STS1 |
Automatic high beam sensor state past 1 / Undetec, CAM NA, Nosens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err |
Condition can be displayed*3 |
Although the item is displayed on the Techstream, it is not applicable to the vehicle. |
|
Auto H Beam STS2 |
Automatic high beam sensor state past 2 / Undetec, CAM NA, Nosens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err |
Condition can be displayed*3 |
Although the item is displayed on the Techstream, it is not applicable to the vehicle. |
|
Auto H Beam STS3 |
Automatic high beam sensor state past 3 / Undetec, CAM NA, Nosens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err |
Condition can be displayed*3 |
Although the item is displayed on the Techstream, it is not applicable to the vehicle. |
|
Auto H Beam STS4 |
Automatic high beam sensor state past 4 / Undetec, CAM NA, Nosens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err |
Condition can be displayed*3 |
Although the item is displayed on the Techstream, it is not applicable to the vehicle. |
|
Auto H Beam STS5 |
Automatic high beam sensor state past 5 / Undetec, CAM NA, Nosens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err |
Condition can be displayed*3 |
Although the item is displayed on the Techstream, it is not applicable to the vehicle. |
|
Auto H Beam STS6 |
Automatic high beam sensor state past 6 / Undetec, CAM NA, Nosens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err |
Condition can be displayed*3 |
Although the item is displayed on the Techstream, it is not applicable to the vehicle. |
|
Auto H Beam STS7 |
Automatic high beam sensor state past 7 / Undetec, CAM NA, Nosens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err |
Condition can be displayed*3 |
Although the item is displayed on the Techstream, it is not applicable to the vehicle. |
- *1: w/ Smart Key System
- *2: w/ DRL OFF Switch
HINT:
*3: The details of each value of the Control Range are as follows:
|
Range |
Condition |
Control Condition |
Diagnostic Note |
|---|---|---|---|
|
Undetec |
Automatic high beam sensor being initialized |
Control suspended (low beam headlights illuminated) |
- |
|
CAM NA |
Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc. |
Control suspended (low beam headlights illuminated) |
- |
|
No sens |
No lights detected |
High beam headlights illuminated |
Only when vehicle speed within operation speed range |
|
Hlight |
Headlights of oncoming vehicle, etc. detected |
Low beam headlights illuminated |
Only when vehicle speed within operation speed range |
|
Taillgt |
Taillights preceding vehicle, etc. detected |
Low beam headlights illuminated |
Only when vehicle speed within operation speed range |
|
Speed |
No lights detected and vehicle speed below operation speed |
Low beam headlights illuminated |
- |
|
Daytime |
Bright light detected |
Low beam headlights illuminated |
- |
|
Village |
Streetlights, etc. detected |
Low beam headlights illuminated |
Only when vehicle speed within operation speed range |
|
Delay |
Changing between low beams and high beams |
Changing between low beams and high beams |
Only when vehicle speed within operation speed range |
|
Malfunc |
Not applicable |
- |
- |
|
Aim Lmt |
|||
|
SAE Mod |
|||
|
Undefin |
|||
|
LIN Err |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Turn Signal Switch (Right) |
Turn signal switch (right) signal / ON or OFF |
ON: Turn signal switch (right) on OFF: Turn signal switch (right) off |
- |
|
Turn Signal Switch (Left) |
Turn signal switch (left) signal / ON or OFF |
ON: Turn signal switch (left) on OFF: Turn signal switch (left) off |
- |
|
Hazard Flasher Switch |
Hazard warning signal switch signal / ON or OFF |
ON: Hazard warning signal switch on OFF: Hazard warning signal switch off |
- |
|
Turn Switch Signal (Full Turn) |
Turn signal switch (full turn) signal / ON or OFF |
ON: Turn signal switch (left or right) on OFF: Turn signal switch (left and right) off |
- |
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body or Smart Key / Active Test.
(e) According to the display on the Techstream, perform the "Active Test".
Main Body|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Daytime Running Light |
Daytime running lights |
ON/OFF |
- |
|
Illuminated Entry System |
Turns on the lights that are controlled by the illuminated entry system* |
ON or OFF |
Perform the Active Test with interior light DOOR switch in the map light assembly turned on. |
|
Cargo Light |
Cargo light |
ON/OFF |
- |
|
Taillight Relay |
Taillight relay |
ON/OFF |
- |
|
Headlight Relay |
Headlight relay (Low beam headlights) |
ON/OFF |
- |
|
Head Light Hi |
High beam headlights |
ON/OFF |
- |
|
Front Fog Light Relay |
Front fog light relay |
ON/OFF |
Light control switch in tail position |
|
Relay for Interior Light Auto Cut Function |
DOME CUT relay |
ON/OFF |
When performing this Active Test, turn on each interior lights.
|
- *: Refer to Description for the lights that are controlled by the illuminated
entry system (See page
.gif)
).
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Automatic High Beam Indicator* |
Automatic High Beam Indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
- *: w/ Automatic High Beam System
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power/Engine SW Light |
Engine Switch illumination* |
ON/OFF |
When performing this Active Test, make sure the following condition is met: The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the ignition switch is ON or ACC, or the engine is running |
- *: w/ Smart Key System
Light Sensor Circuit Malfunction (B1244)
DESCRIPTION
This DTC is output when a failure of the automatic light control sensor circuit
is detected.
DTC Code
DTC Detection Condition
Trouble Area
...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
HINT:
If a trouble code is displayed during the DTC check, inspect the trouble areas
listed for that code. For details of the code, refer to the "See page" ...
Other materials:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are listed in order of probability in the "Suspected Area" column of the
table. Check each sy ...
Removal
REMOVAL
CAUTION / NOTICE / HINT
NOTICE:
Replace the blind spot monitor sensor if it has been dropped or subjected to
a severe impact.
PROCEDURE
1. REMOVE REAR BUMPER ASSEMBLY (w/ Towing Package)
(See page )
2. REMOVE REAR BUMPER ASSEMBLY (w/o Towing Package)
(See page )
3. REMOVE CONN ...
Open in ABS Solenoid Relay Circuit (C146E,C146F)
DESCRIPTION
The ABS solenoid relay supplies power to the ABS solenoid and TRAC solenoid.
The solenoid relay is turned on 1.5 seconds after the ignition switch is turned
ON, and is turned off if an open or short in the solenoid is detected by the self
diagnosis performed when the engine starts ...
