Toyota Tacoma (2015-2018) Service Manual: Rear Speed Sensor RH Performance (C1411,C1412)

Toyota Tacoma (2015-2018) Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Hydraulic Brake Booster) / Rear Speed Sensor RH Performance (C1411,C1412)

DESCRIPTION

Refer to DTCs C1401 and C1402 (See page ).

DTC Code	DTC Detection Condition	Trouble Area
C1411 C1412	One of the following conditions is met: When the vehicle is driven in reverse at a speed of 3 km/h (2 mph) or more and 3 of the wheel sensors detect the reverse signal, the other sensor detects a high frequency pulse 75 times while the ignition switch is ON. At a vehicle speed of 10 km/h (6 mph) or more, the vehicle speed sensor output drops by 50% for 5 seconds. The lowest wheel speed is 10 km/h (6 mph) or more and the difference between the highest and lowest wheel speed values is 2 km/h (1 mph) or less for 15 seconds. At a vehicle speed of 30 km/h (19 mph) or more, one wheel direction is different from the other 3 wheels for 1 second. At a vehicle speed of 100 km/h (62 mph), a reverse signal is output for 1 second or more. At a vehicle speed of 30 km/h (19 mph) or more, the rotation direction of one of the wheels is not detected normally and the rotation direction of the other 3 wheels is not the same for 1 second.	Rear speed sensor RH/LH

DTC Code

DTC Detection Condition

Trouble Area

C1411

C1412

One of the following conditions is met:

When the vehicle is driven in reverse at a speed of 3 km/h (2 mph) or more and 3 of the wheel sensors detect the reverse signal, the other sensor detects a high frequency pulse 75 times while the ignition switch is ON.
At a vehicle speed of 10 km/h (6 mph) or more, the vehicle speed sensor output drops by 50% for 5 seconds.
The lowest wheel speed is 10 km/h (6 mph) or more and the difference between the highest and lowest wheel speed values is 2 km/h (1 mph) or less for 15 seconds.
At a vehicle speed of 30 km/h (19 mph) or more, one wheel direction is different from the other 3 wheels for 1 second.
At a vehicle speed of 100 km/h (62 mph), a reverse signal is output for 1 second or more.
At a vehicle speed of 30 km/h (19 mph) or more, the rotation direction of one of the wheels is not detected normally and the rotation direction of the other 3 wheels is not the same for 1 second.

Rear speed sensor RH/LH

HINT:

DTC C1411 is for the rear speed sensor RH.
DTC C1412 is for the rear speed sensor LH.

CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after replacement (See page PROCEDURE ).

PROCEDURE

1.	REPLACE REAR SPEED SENSOR

(a) Replace the rear speed sensor (See page ).

END

Front Speed Sensor RH Performance (C1409,C1410)

DESCRIPTION Refer to DTCs C1401 and C1402 (See page ). DTC Code DTC Detection Condition Trouble Area C1409 C1410 One of the following ...

High Power Supply Voltage Malfunction (C1417)

DESCRIPTION If a malfunction is detected in the power supply circuit, the skid control ECU (housed in the master cylinder solenoid) stores this DTC and the fail-safe function prohibits ABS/VSC/TR ...

Other materials:

Four Wheel Drive (4WD) Range Signal Circuit Range / Performance (P279E)
DESCRIPTION When the transfer position switch is switched, the 2-4 terminal and LO terminal change to one of the following ON/OFF combinations listed in the table below. Terminal 2WD Between 2WD and H4 H4 Between H4 and L4 L4 ...

Satellite Radio Broadcast cannot be Received
CAUTION / NOTICE / HINT NOTICE: Some satellite radio broadcasts require payment. A contract must be made between a satellite radio company and the user. If the contract expires, it will not be possible to listen to the broadcast. After replacing the stereo component tuner assem ...

Automatic High Beam System does not Operate or Operation Indicator does not Illuminate
DESCRIPTION The main body ECU (multiplex network body ECU) controls the automatic high beam system based on signals received from the forward recognition camera. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: When replacing the combination meter assembly, always replace it with ...