Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Data List / Active Test

Toyota Tacoma (2015-2018) Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Vacuum Brake Booster) / Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Warm up the engine.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

(f) According to the display on the Techstream, read the Data List.

ABS/VSC/TRAC

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

ABS Warning Light

ABS warning light/ ON or OFF

OFF

-

Brake Warning Light

Brake warning light/ ON or OFF

OFF

-

Stop Light SW

Stop light switch/ ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Parking Brake SW

Parking brake switch/ ON or OFF

ON: Parking brake applied

OFF: Parking brake released

-

Gear Position

Gear position/ Fail, 1st-10th, P/N, R or Not R

Actual gear position

-

Shift Lever Position

Shift lever position/ Fail, 1st-6th/B, D/M, P/N or R

Actual shift lever position

-

Inspection Mode

Inspection mode/ Other or Inspect

Other: Normal mode

Inspect: Inspection mode

-

Zero Point of M/C

Memorized zero value/ Min.: -12.50 Mpa, Max.: 12.40 Mpa

-

-

Deceleration Sensor

Deceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2

-

Changes continuously during acceleration/deceleration.

Zero Point of Decele

Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Deceleration Sensor2

Deceleration sensor 2 reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2

-

Changes continuously during acceleration/deceleration.

Zero Point of Decele2

Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Yaw Rate Sensor

Yaw rate and deceleration sensor 1/ Min.: -128 °/s, Max.: 127 °/s

0 °/s: Vehicle stationary

-128 to 0 °/s: Right turn

0 to 127 °/s: Left turn

-

Zero Point of Yaw Rate

Memorized zero value/ Min.: -128 °, Max.: 127 °

-

-

Steering Angle Sensor

Steering angle sensor/ Min.: -3276.8 °, Max.: 3276.7 °

Left turn: Increases

Right turn: Decreases

-

Zero Point of Steering Angle

Memorized zero value/ Min.: -3276.8 °, Max.: 3276.7 °

-

-

Lateral G

Lateral G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

Changes in proportion with acceleration during turning.

Forward and Rearward G

Forward and rearward G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

Changes in proportion with acceleration during acceleration/deceleration.

Yaw Rate Value

Yaw rate value/ Min.: -128 °/s, Max.: 127 °/s

-

Changes in proportion with yaw during turning.

Steering Angle Value

Steering angle value/ Min.: -3276.8 °, Max.: 3276.7 °

-

Changes in proportion with the amount of steering wheel rotation during steering operation.

Stop Light Relay

Stop light control relay (STOP LP)/ ON or OFF

ON: Relay on

OFF: Relay off

-

Slip Indicator Light

Slip indicator light/ ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

Rear Diff Lock Switch

Rear differential lock detection switch/ ON or OFF

ON: Rear differential lock detection switch on

OFF: Rear differential lock detection switch off

-

Automatic Disconnect Diff SW

A.D.D. actuator 4WD detection switch/ ON or OFF

ON: 4WD

OFF: 2WD

-

L4 Switch

Transfer L4 detection switch/ ON or OFF

ON: L4

OFF: except L4

-

FR Wheel Speed

Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual wheel speed

No large fluctuations when driving at a constant speed.

FL Wheel Speed

Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual wheel speed

No large fluctuations when driving at a constant speed.

RR Wheel Speed

Rear wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual wheel speed

No large fluctuations when driving at a constant speed.

RL Wheel Speed

Rear wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual wheel speed

No large fluctuations when driving at a constant speed.

Vehicle Speed

Maximum wheel speed sensor reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual vehicle speed

No large fluctuations when driving at a constant speed.

FR Wheel Acceleration

Front wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

Changes continuously during acceleration/deceleration.

FL Wheel Acceleration

Front wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

Changes continuously during acceleration/deceleration.

RR Wheel Acceleration

Rear wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

Changes continuously during acceleration/deceleration.

RL Wheel Acceleration

Rear wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

Changes continuously during acceleration/deceleration.

Stop Light Relay Output

Stop light control relay (STOP LP) output/ ON or OFF

ON: Relay on (Stop light on)

OFF: Relay off (Stop light off)

-

Auto LSD Indicator Light

Auto LSD indicator light/ ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

FR Wheel ABS Ctrl Status

Front wheel RH ABS control status/ ON or OFF

ON: During control

OFF: Not during control

-

FL Wheel ABS Ctrl Status

Front wheel LH ABS control status/ ON or OFF

ON: During control

OFF: Not during control

-

RR Wheel ABS Ctrl Status

Rear wheel RH ABS control status/ ON or OFF

ON: During control

OFF: Not during control

-

RL Wheel ABS Ctrl Status

Rear wheel LH ABS control status/ ON or OFF

ON: During control

OFF: Not during control

-

BA Ctrl Status

BA control status/ ON or OFF

ON: During control

OFF: Not during control

-

PBA Ctrl Status

PBA control status/ ON or OFF

ON: During control

OFF: Not during control

-

TRC (TRAC) Ctrl Status

Traction control status/ ON or OFF

ON: During control

OFF: Not during control

-

TRC (TRAC) Engine Ctrl Status

Traction control (engine control) status/ ON or OFF

ON: During control

OFF: Not during control

-

TRC (TRAC) Brake Ctrl Status

Traction control (brake control) status/ ON or OFF

ON: During control

OFF: Not during control

-

FR Wheel VSC Ctrl Status

Front wheel RH VSC control status/ ON or OFF

ON: During control

OFF: Not during control

-

FL Wheel VSC Ctrl Status

Front wheel LH VSC control status/ ON or OFF

ON: During control

OFF: Not during control

-

RR Wheel VSC Ctrl Status

Rear wheel RH VSC control status/ ON or OFF

ON: During control

OFF: Not during control

-

RL Wheel VSC Ctrl Status

Rear wheel LH VSC control status/ ON or OFF

ON: During control

OFF: Not during control

-

Engine Revolutions

Engine speed/ Min.: 0 rpm, Max.: 65535 rpm

Actual engine speed

-

Real Engine Torque

Actual engine torque/ Min.: -1024.0 Nm, Max.: 1023.0 Nm

-

-

Accelerator Opening Angle %

Percentage of accelerator pedal opening angle/ Min.: 0.0 %, Max.: 127.5 %

0 %: When accelerator pedal released

Changes in proportion with the movement of the pedal during accelerator pedal operation.

Solenoid Relay

Solenoid relay/ ON or OFF

ON: Solenoid relay on

OFF: Solenoid relay off

-

ECB (Electronically Controlled Brake system) Motor Relay

ECB (Electronically Controlled Brake) motor relay/ ON or OFF

ON: Motor relay on

OFF: Motor relay off

-

TR(A)C/VSC Solenoid (SM2)

Master cut solenoid (SM2)/ ON or OFF

ON: Operating

OFF: Not operating

-

TR(A)C/VSC Solenoid (SM1)

Master cut solenoid (SM1)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFRH)

ABS solenoid (SFRH)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFRR)

ABS solenoid (SFRR)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFLH)

ABS solenoid (SFLH)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFLR)

ABS solenoid (SFLR)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRRH)

ABS solenoid (SRRH)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRRR)

ABS solenoid (SRRR)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRLH)

ABS solenoid (SRLH)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRLR)

ABS solenoid (SRLR)/ ON or OFF

ON: Operating

OFF: Not operating

-

FR Speed Open

Front speed sensor RH open circuit detection/ Error or Normal

Normal

-

FL Speed Open

Front speed sensor LH open circuit detection/ Error or Normal

Normal

-

RR Speed Open

Rear speed sensor RH open circuit detection/ Error or Normal

Normal

-

RL Speed Open

Rear speed sensor LH open circuit detection/ Error or Normal

Normal

-

EFI Communication Open

ECM communication open circuit detection/ Error or Normal

Normal

-

Yaw Rate Open

Yaw rate and deceleration sensor open circuit detection/ Error or Normal

Normal

-

Deceleration Open

Deceleration sensor open circuit detection/ Error or Normal

Normal

-

Steering Open

Steering angle sensor open circuit detection/ Error or Normal

Normal

-

Master Cylinder Open

Master cylinder pressure sensor open circuit detection/ Error or Normal

Normal

-

IG1 Voltage Value

IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V

11 to 14 V

Changes in proportion to battery voltage

IG2 Voltage Value

IG2 voltage value/ Min.: 0.00 V, Max.: 20.00 V

11 to 14 V

Changes in proportion to battery voltage

BS1 Voltage Value

BS1 voltage value/ Min.: 0.00 V, Max.: 20.00 V

11 to 14 V

Changes in proportion to battery voltage

MT Voltage Value

Motor voltage value/ Min.: 0.00 V, Max.: 20.00 V

11 to 14 V

Changes in proportion to battery voltage

TRAC/VSC Off Mode

TRAC/VSC off mode/ Normal, TRAC OFF, VSC Expert Mode or VSC OFF

Normal: Normal

TRAC OFF: TRAC OFF mode

VSC Expert Mode: VSC expert mode

VSC OFF: VSC OFF mode

-

Number of DTC

Number of DTCs/ Min.: 0, Max.: 255

0

-

FR Speed Sensor Voltage Open

Front speed sensor RH voltage open circuit detection/ Error or Normal

Normal

-

FL Speed Sensor Voltage Open

Front speed sensor LH voltage open circuit detection/ Error or Normal

Normal

-

RR Speed Sensor Voltage Open

Rear speed sensor RH voltage open circuit detection/ Error or Normal

Normal

-

RL Speed Sensor Voltage Open

Rear speed sensor LH voltage open circuit detection/ Error or Normal

Normal

-

M/C Pressure Sensor Noise

Master cylinder pressure sensor noise detection/ Error or Normal

Normal

-

Yaw Rate Sensor Voltage Open

Yaw rate and deceleration sensor voltage open circuit detection/ Error or Normal

Normal

-

EFI Communication Invalid

ECM communication invalid detection/ Error or Normal

Normal

-

Reverse Position Switch

Shift lever R position status/ ON or OFF

ON: Shift lever is in R

OFF: Shift lever is not in R

-

Master Cylinder Pressure

Master cylinder pressure sensor pressure/ Min.: 0.00 MPa, Max.: 24.48 MPa

Brake pedal operated: Proportional to pedal force

Brake pedal released: 0.00 to 1.76 MPa

-

Master Cylinder Sensor Temperature

Master cylinder pressure sensor temperature/ Min.: -80 °C (-112 °F), Max.: 175 °C (347 °F)

Displays current master cylinder temperature

-

Motor Power Supply Voltage

Motor power source voltage/ Min.: 0.00 V, Max.: 20.00 V

11 to 14 V

Changes in proportion to battery voltage

Solenoid Power Supply Voltage

Solenoid power source voltage/ Min.: 0.00 V, Max.: 20.00 V

11 to 14 V

Changes in proportion to battery voltage

Stop Light Relay State for ECU Control

Stop light control relay (for ECU control)/ ON or OFF

ON: Stop light control relay operating

OFF: Stop light control relay not operating

-

Solenoid State for ECU Control

Solenoid (for ECU control)/ ON or OFF

ON: Solenoid relay operating

OFF: Solenoid relay not operating

-

Motor State for ECU Control

Motor (for ECU control)/ ON or OFF

ON: Motor relay operating

OFF: Motor relay not operating

-

Operation History of IG OFF while Vehicle is moving

History of ignition switch turned off when vehicle is in motion/ON or OFF

OFF: No history

ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher

-

Master Cylinder Pressure Sensor Power Supply Open

Master cylinder pressure sensor power supply voltage status/ Error or Normal

Normal

-

Solenoid Power Supply Open

Solenoid power supply voltage status/ Error or Normal

Normal

-

Motor Power Supply Open

Motor power supply voltage status/ Error or Normal

Normal

-

Stop Switch Open

Momentary interruption (open circuit) in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status/ Error or Normal

Normal

-
  • *1: for Manual transmission
  • *2: for Automatic transmission

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

(f) According to the display on the Techstream, perform the Active Test.

ABS/VSC/TRAC

Tester Display

Test Part

Control Range

Diagnostic Note

ABS Warning Light

ABS warning light

Warning light OFF/ON

Observe the combination meter.

[Vehicle condition]

Vehicle stopped

Brake Warning Light

BRAKE warning light

Warning light OFF/ON

Observe the combination meter.

[Vehicle condition]

Vehicle stopped

Solenoid Relay

Solenoid relay

Relay OFF/ON

An operating sound of the solenoid (clicking sound) can be heard.

[Vehicle condition]

Vehicle stopped

Motor Relay

Motor relay

Relay OFF/ON

An operating sound of the motor can be heard (does not come on for 2 to 5 seconds).

[Vehicle condition]

Vehicle stopped

Stop Light Relay

Stop light control relay (STOP LP CTRL)

Relay OFF/ON

Observe the stop light (does not come on for 2 to 5 seconds).

[Vehicle condition]

Vehicle stopped

ABS Solenoid (SRLR)

ABS solenoid (SRLR)

Solenoid OFF/ON

An operating sound of the solenoid (clicking sound) can be heard (does not come on for 2 to 5 seconds).

[Vehicle condition]

Vehicle stopped

Parking brake applied

Shift lever is in P (neutral)

ABS Solenoid (SRLH)

ABS solenoid (SRLH)

Solenoid OFF/ON

ABS Solenoid (SRRR)

ABS solenoid (SRRR)

Solenoid OFF/ON

ABS Solenoid (SRRH)

ABS solenoid (SRRH)

Solenoid OFF/ON

ABS Solenoid (SFLR)

ABS solenoid (SFLR)

Solenoid OFF/ON

ABS Solenoid (SFLH)

ABS solenoid (SFLH)

Solenoid OFF/ON

ABS Solenoid (SFRR)

ABS solenoid (SFRR)

Solenoid OFF/ON

ABS Solenoid (SFRH)

ABS solenoid (SFRH)

Solenoid OFF/ON

VSC/TRAC Solenoid (SMR)

Master cut solenoid (SM2)

Solenoid OFF/ON

An operating sound of the solenoid (clicking sound) can be heard.

[Vehicle condition]

Vehicle stopped

VSC/TRAC Solenoid (SMF)

Master cut solenoid (SM1)

Solenoid OFF/ON

An operating sound of the solenoid (clicking sound) can be heard.

[Vehicle condition]

Vehicle stopped

TRC(TRAC) OFF Indicator Light

TRAC OFF indicator light

Indicator light OFF/ON

Observe the combination meter.

[Vehicle condition]

Vehicle stopped

VSC OFF Indicator Light

VSC OFF indicator light

Indicator light OFF/ON

Observe the combination meter.

[Vehicle condition]

Vehicle stopped

Slip Indicator Light

Slip indicator light

Indicator light OFF/ON

Observe the combination meter.

[Vehicle condition]

Vehicle stopped

Auto LSD Indicator Light

Auto LSD indicator light

Indicator light OFF/ON

Observe the combination meter.

[Vehicle condition]

Vehicle stopped

ABS Solenoid

ABS solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH)

Solenoid SFRH/SFRR/SFLH/SFLR/SRRH/SRRR/SRLH/SRLR

An operating sound of the solenoid (clicking sound) can be heard (does not come on for 2 to 5 seconds).

[Vehicle condition]

Vehicle stopped

Parking brake applied

Shift lever is in P (neutral)

VSC/TRC(TRAC) Solenoid

Master cut solenoid (SM1, SM2)

Solenoid SRCF/SRCR/SRMF/SRMR/SMF/SMR/SPFR/SPFL
Freeze Frame Data
FREEZE FRAME DATA 1. FREEZE FRAME DATA (a) Using the Techstream, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output. 2. CHECK FREEZE FRAME DATA WHEN BRAKE ...

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART VSC System DTC Code Detection Item See page C1201 Engine Control System Malfunction ...

Other materials:

Main Body ECU Vehicle Information Reading/Writing Process Malfunction (B15F6)
DESCRIPTION This DTC is stored when items controlled by the main body ECU (multiplex network body ECU) cannot be customized via the audio and visual system vehicle customization screen. HINT: The main body ECU (multiplex network body ECU) controls the items for the following systems th ...

Low Power Supply Voltage Malfunction (C1241)
DESCRIPTION If there is a problem with the skid control ECU (master cylinder solenoid) power supply circuit, the skid control ECU outputs the DTC and prohibits operation under the fail-safe function. If the voltage supplied to terminal IG1 is not within the DTC detection threshold due to mal ...

Parking Brake Switch Circuit
DESCRIPTION This circuit is from the parking brake switch assembly to the navigation receiver assembly. WIRING DIAGRAM PROCEDURE 1. CHECK VEHICLE SIGNAL (OPERATION CHECK) (a) Display the "Vehicle Signal Check Mode" screen (See page ). ...

© 2011-2024 Copyright www.ttguide.net