Toyota Tacoma (2015-2018) Service Manual: Data List / Active Test

Toyota Tacoma (2015-2018) Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Hydraulic Brake Booster) / Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Warm up the engine.

(b) Connect the Techstream to the DLC3.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

(f) According to the display on the Techstream, read the Data List.

ABS/VSC/TRAC

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
ABS Warning Light	ABS warning light/ ON or OFF	OFF	-
Brake Warning Light	Brake warning light/ ON or OFF	OFF	-
Buzzer	VSC warning buzzer/ ON or OFF	ON: Buzzer on OFF: Buzzer off	-
Stop Light SW	Stop light switch/ ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-
Parking Brake SW	Parking brake switch/ ON or OFF	ON: Parking brake applied OFF: Parking brake released	-
Reservoir Warning SW	Brake fluid level warning switch/ ON or OFF	OFF	-
Main Idle SW	Main idle switch/ ON or OFF	ON: Accelerator pedal released OFF: Accelerator pedal depressed	-
Gear Position	Gear position/ Fail, 1st-10th, P/N, R or Not R	Actual gear position	-
Shift Lever Position	Shift lever position/ Fail, 1st-6th/B, D/M, P/N or R	Actual shift lever position	-
Shift Information	Shift information/ ON or OFF	ON: During gear change OFF: Not during gear change	-
Inspection Mode	Inspection mode/ Other or Inspect	Other: Normal mode Inspect: Inspection mode	-
Number of IG ON (Inspection)	Number of times ignition switch turned ON after entering inspection mode/ Min.: 0, Max.: 255	-	-
Master Cylinder Sensor	Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V	0.3 to 0.9 V: When brake pedal released	The value increases when the brake pedal is depressed.
Zero Point of M/C	Memorized zero value/ Min.: -12.50 MPa, Max.: 12.40 MPa	-	-
Accumulator Sensor	Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V	3.58 to 5 V	If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.
Deceleration Sensor	Acceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2	-	Changes continuously during acceleration/deceleration.
Zero Point of Decele	Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2	-	-
Deceleration Sensor2	Acceleration sensor 2 reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2	-	Changes continuously during acceleration/deceleration.
Zero Point of Decele2	Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2	-	-
Yaw Rate Sensor	Yaw rate and acceleration sensor 1/ Min.: -128 °/s, Max.: 127 °/s	0 °/s: Vehicle stationary -128 to 0 °/s: Right turn 0 to 127 °/s: Left turn	-
Zero Point of Yaw Rate	Memorized zero value/ Min.: -128 °, Max.: 127 °	-	-
Zero Point of Yaw Rate2	Memorized zero value/ Min.: -128 °/s, Max.: 127 °/s	-	-
Steering Angle Sensor	Steering angle sensor/ Min.: -3276.8 °, Max.: 3276.7 °	Left turn: Increases Right turn: Decreases	-
Zero Point of Steering Angle	Memorized zero value/ Min.: -3276.8 °, Max.: 3276.7 °	-	-
Lateral G	Lateral G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2	-	Changes in proportion with acceleration during turning.
Forward and Rearward G	Forward and rearward G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2	-	Changes in proportion with acceleration during acceleration/deceleration.
Yaw Rate Value	Yaw rate value/ Min.: -128 °/s, Max.: 127 °/s	-	Changes in proportion with yaw during turning.
Steering Angle Value	Steering angle value/ Min.: -3276.8 °, Max.: 3276.7 °	-	Changes in proportion with the amount of steering wheel rotation during steering operation.
Stop Light Relay	Stop light control relay (STOP LP)/ ON or OFF	ON: Relay on OFF: Relay off	-
Crawl Control Light*2	Crawl indicator light/ ON or OFF	ON: Indicator light on OFF: Indicator light off	-
Slip Indicator Light	Slip indicator light/ ON or OFF	ON: Indicator light on OFF: Indicator light off	-
Rear Diff Lock Switch	Rear differential lock detection switch/ ON or OFF	ON: Rear differential lock detection switch on OFF: Rear differential lock detection switch off	-
Automatic Disconnect Diff SW	A.D.D. actuator 4WD detection switch/ ON or OFF	ON: 4WD OFF: 2WD	-
L4 Switch	Transfer L4 detection switch/ ON or OFF	ON: L4 OFF: except L4	-
FR Wheel Speed	Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Actual wheel speed	No large fluctuations when driving at a constant speed.
FL Wheel Speed	Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Actual wheel speed	No large fluctuations when driving at a constant speed.
RR Wheel Speed	Rear wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Actual wheel speed	No large fluctuations when driving at a constant speed.
RL Wheel Speed	Rear wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Actual wheel speed	No large fluctuations when driving at a constant speed.
Vehicle Speed	Maximum wheel speed sensor reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Actual vehicle speed	No large fluctuations when driving at a constant speed.
FR Wheel Acceleration	Front wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2	-	Changes continuously during acceleration/deceleration.
FL Wheel Acceleration	Front wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2	-	Changes continuously during acceleration/deceleration.
RR Wheel Acceleration	Rear wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2	-	Changes continuously during acceleration/deceleration.
RL Wheel Acceleration	Rear wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2	-	Changes continuously during acceleration/deceleration.
FR Wheel Direction	Front wheel direction RH/ Forward or Back	Forward: Forward Back: Backward	-
FL Wheel Direction	Front wheel direction LH/ Forward or Back	Forward: Forward Back: Backward	-
RR Wheel Direction	Rear wheel direction RH/ Forward or Back	Forward: Forward Back: Backward	-
RL Wheel Direction	Rear wheel direction LH/ Forward or Back	Forward: Forward Back: Backward	-
Stop Light Relay Output	Stop light control relay (STOP LP) output/ ON or OFF	ON: Relay on (Stop light on) OFF: Relay off (Stop light off)	-
Crawl Control Switch*2	Crawl speed selector switch status/ LOW, MIDLOW, MID, MIDHIGH or HIGH	Actual crawl speed selector switch position	-
Auto LSD Indicator Light	Auto LSD indicator light/ ON or OFF	ON: Indicator light on OFF: Indicator light off	-
A-TRAC Indicator Light*1	A-TRAC indicator light/ ON or OFF	ON: Indicator light on OFF: Indicator light off	-
FR Wheel ABS Ctrl Status	Front wheel RH ABS control status/ ON or OFF	ON: During control OFF: Not during control	-
FL Wheel ABS Ctrl Status	Front wheel LH ABS control status/ ON or OFF	ON: During control OFF: Not during control	-
RR Wheel ABS Ctrl Status	Rear wheel RH ABS control status/ ON or OFF	ON: During control OFF: Not during control	-
RL Wheel ABS Ctrl Status	Rear wheel LH ABS control status/ ON or OFF	ON: During control OFF: Not during control	-
RR Wheel EBD Ctrl Status	Rear wheel RH EBD control status/ ON or OFF	ON: During control OFF: Not during control	-
RL Wheel EBD Ctrl Status	Rear wheel LH EBD control status/ ON or OFF	ON: During control OFF: Not during control	-
BA Ctrl Status	BA control status/ ON or OFF	ON: During control OFF: Not during control	-
PBA Ctrl Status	PBA control status/ ON or OFF	ON: During control OFF: Not during control	-
TRC (TRAC) Ctrl Status	Traction control status/ ON or OFF	ON: During control OFF: Not during control	-
TRC (TRAC) Engine Ctrl Status	Traction control (engine control) status/ ON or OFF	ON: During control OFF: Not during control	-
TRC (TRAC) Brake Ctrl Status	Traction control (brake control) status/ ON or OFF	ON: During control OFF: Not during control	-
FR Wheel VSC Ctrl Status	Front wheel RH VSC control status/ ON or OFF	ON: During control OFF: Not during control	-
FL Wheel VSC Ctrl Status	Front wheel LH VSC control status/ ON or OFF	ON: During control OFF: Not during control	-
RR Wheel VSC Ctrl Status	Rear wheel RH VSC control status/ ON or OFF	ON: During control OFF: Not during control	-
RL Wheel VSC Ctrl Status	Rear wheel LH VSC control status/ ON or OFF	ON: During control OFF: Not during control	-
Engine Revolutions	Engine speed/ Min.: 0 rpm, Max.: 65535 rpm	Actual engine speed	-
Real Engine Torque	Actual engine torque/ Min.: -1024.0 Nm, Max.: 1023.0 Nm	-	-
Accelerator Opening Angle %	Percentage of accelerator pedal opening angle/ Min.: 0.0 %, Max.: 127.5 %	0 %: When accelerator pedal released	Changes in proportion with the movement of the pedal during accelerator pedal operation.
Solenoid Relay	Solenoid relay/ ON or OFF	ON: Solenoid relay on OFF: Solenoid relay off	-
ECB (Electronically Controlled Brake system) Motor Relay	ECB (Electronically Controlled Brake) motor relay/ ON or OFF	ON: Motor relay on OFF: Motor relay off	-
TR(A)C/VSC Solenoid (SRM2)	TRAC/VSC solenoid (STR)/ ON or OFF	ON: Operating OFF: Not operating	-
TR(A)C/VSC Solenoid (SRM1)	TRAC/VSC solenoid (SREC)/ ON or OFF	ON: Operating OFF: Not operating	-
TR(A)C/VSC Solenoid (SRC2)	TRAC/VSC solenoid (SREA)/ ON or OFF	ON: Operating OFF: Not operating	-
TR(A)C/VSC Solenoid (SRC1)	TRAC/VSC solenoid (SMCF)/ ON or OFF	ON: Operating OFF: Not operating	-
ABS Solenoid (SFRH)	ABS solenoid (SFRH)/ ON or OFF	ON: Operating OFF: Not operating	-
ABS Solenoid (SFRR)	ABS solenoid (SFRR)/ ON or OFF	ON: Operating OFF: Not operating	-
ABS Solenoid (SFLH)	ABS solenoid (SFLH)/ ON or OFF	ON: Operating OFF: Not operating	-
ABS Solenoid (SFLR)	ABS solenoid (SFLR)/ ON or OFF	ON: Operating OFF: Not operating	-
ABS Solenoid (SRRH)	ABS solenoid (SRRH)/ ON or OFF	ON: Operating OFF: Not operating	-
ABS Solenoid (SRRR)	ABS solenoid (SRRR)/ ON or OFF	ON: Operating OFF: Not operating	-
ABS Solenoid (SRLH)	ABS solenoid (SRLH)/ ON or OFF	ON: Operating OFF: Not operating	-
ABS Solenoid (SRLR)	ABS solenoid (SRLR)/ ON or OFF	ON: Operating OFF: Not operating	-
FR Speed Open	Front speed sensor RH open circuit detection/ Error or Normal	Normal	-
FL Speed Open	Front speed sensor LH open circuit detection/ Error or Normal	Normal	-
RR Speed Open	Rear speed sensor RH open circuit detection/ Error or Normal	Normal	-
RL Speed Open	Rear speed sensor LH open circuit detection/ Error or Normal	Normal	-
EFI Communication Open	ECM communication open circuit detection/ Error or Normal	Normal	-
Yaw Rate Open	Yaw rate and acceleration sensor open circuit detection/ Error or Normal	Normal	-
Deceleration Open	Acceleration sensor open circuit detection/ Error or Normal	Normal	-
Steering Open	Steering angle sensor open circuit detection/ Error or Normal	Normal	-
Master Cylinder Open	Master cylinder pressure sensor open circuit detection/ Error or Normal	Normal	-
IG1 Voltage Value	IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V	11 to 14 V	Changes in proportion to battery voltage
IG2 Voltage Value	IG2 voltage value/ Min.: 0.00 V, Max.: 20.00 V	11 to 14 V	Changes in proportion to battery voltage
TRAC/VSC Off Mode	TRAC/VSC off mode/ Normal, TRAC OFF, VSC Expert Mode or VSC OFF	Normal: Normal TRAC OFF: TRAC OFF mode VSC Expert Mode: VSC expert mode VSC OFF: VSC OFF mode	-
Number of DTC	Number of DTCs/ Min.: 0, Max.: 255	0	-
IG Voltage Value Decreased	IG1 voltage value decreased/ Error or Normal	Normal	-
IG Voltage Value Increased	IG1 voltage value increased/ Error or Normal	Normal	-
FR Speed Sensor Voltage Open	Front speed sensor RH voltage open circuit detection/ Error or Normal	Normal	-
FL Speed Sensor Voltage Open	Front speed sensor LH voltage open circuit detection/ Error or Normal	Normal	-
RR Speed Sensor Voltage Open	Rear speed sensor RH voltage open circuit detection/ Error or Normal	Normal	-
RL Speed Sensor Voltage Open	Rear speed sensor LH voltage open circuit detection/ Error or Normal	Normal	-
M/C Pressure Sensor Noise	Master cylinder pressure sensor noise detection/ Error or Normal	Normal	-
Yaw Rate Sensor Voltage Open	Yaw rate and acceleration sensor voltage open circuit detection/ Error or Normal	Normal	-
EFI Communication Invalid	ECM communication invalid detection/ Error or Normal	Normal	-
A-TRC(TRAC) Switch*1	A-TRC(TRAC) Switch/ ON or OFF	ON: A-TRC switch on OFF: A-TRC switch off	-
Operation History of IG OFF while Vehicle is moving	History of ignition switch turned off when vehicle is in motion/ON or OFF	OFF: No history ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher	-

*1: for Manual transmission
*2: for Automatic transmission

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Connect the Techstream to the DLC3.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

(f) According to the display on the Techstream, perform the Active Test.

ABS/VSC/TRAC

Tester Display	Test Part	Control Range	Diagnostic Note
ABS Warning Light	ABS warning light	Warning light OFF/ON	Observe the combination meter. [Vehicle condition] Vehicle stopped
Brake Warning Light	BRAKE warning light	Warning light OFF/ON	Observe the combination meter. [Vehicle condition] Vehicle stopped
Buzzer	VSC warning buzzer	Buzzer OFF/ON	The buzzer can be heard. [Vehicle condition] Vehicle stopped
Solenoid Relay	Solenoid relay	Relay OFF/ON	An operating sound of the solenoid (clicking sound) can be heard. [Vehicle condition] Vehicle stopped
Motor Relay	Motor relay	Relay OFF/ON	An operating sound of the motor can be heard (does not come on for 2 to 5 seconds). [Vehicle condition] Vehicle stopped
Stop Light Relay	Stop light control relay (STOP LP CTRL)	Relay OFF/ON	Observe the stop light (does not come on for 2 to 5 seconds). [Vehicle condition] Vehicle stopped
ABS Solenoid (SRLR)	ABS solenoid (SRLR)	Solenoid OFF/ON	An operating sound of the solenoid (clicking sound) can be heard (does not come on for 2 to 5 seconds). [Vehicle condition] Vehicle stopped Parking brake applied Shift lever is in P (neutral)
ABS Solenoid (SRLH)	ABS solenoid (SRLH)	Solenoid OFF/ON
ABS Solenoid (SRRR)	ABS solenoid (SRRR)	Solenoid OFF/ON
ABS Solenoid (SRRH)	ABS solenoid (SRRH)	Solenoid OFF/ON
ABS Solenoid (SFLR)	ABS solenoid (SFLR)	Solenoid OFF/ON
ABS Solenoid (SFLH)	ABS solenoid (SFLH)	Solenoid OFF/ON
ABS Solenoid (SFRR)	ABS solenoid (SFRR)	Solenoid OFF/ON
ABS Solenoid (SFRH)	ABS solenoid (SFRH)	Solenoid OFF/ON
VSC/TRAC Solenoid (SRMR)	VSC/TRAC solenoid (STR)	Solenoid OFF/ON	An operating sound of the solenoid (clicking sound) can be heard (does not come on for 2 to 5 seconds). [Vehicle condition] Vehicle stopped Parking brake applied Shift lever is in P (neutral)
VSC/TRAC Solenoid (SRMF)	VSC/TRAC solenoid (SREC)	Solenoid OFF/ON
VSC/TRAC Solenoid (SRCR)	VSC/TRAC solenoid (SREA)	Solenoid OFF/ON
VSC/TRAC Solenoid (SRCF)	VSC/TRAC solenoid (SMCF)	Solenoid OFF/ON
Crawl Control Light*1	CRAWL indicator light	Indicator light OFF/ON	Observe the combination meter. [Vehicle condition] Vehicle stopped
TRC(TRAC) OFF Indicator Light	TRAC OFF indicator light	Indicator light OFF/ON	Observe the combination meter. [Vehicle condition] Vehicle stopped
VSC OFF Indicator Light	VSC OFF indicator light	Indicator light OFF/ON	Observe the combination meter. [Vehicle condition] Vehicle stopped
Slip Indicator Light	Slip indicator light	Indicator light OFF/ON	Observe the combination meter. [Vehicle condition] Vehicle stopped
Auto LSD Indicator Light	Auto LSD indicator light	Indicator light OFF/ON	Observe the combination meter. [Vehicle condition] Vehicle stopped
ABS Solenoid	ABS solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH)	Solenoid SFRH/SFRR/SFLH/SFLR/SRRH/SRRR/SRLH/SRLR	An operating sound of the solenoid (clicking sound) can be heard (does not come on for 2 to 5 seconds). [Vehicle condition] Vehicle stopped Parking brake applied Shift lever is in P (neutral)
VSC/TRC(TRAC) Solenoid	Master cut solenoid (STR, SREC, SREA, SMCF)	Solenoid SRCF/SRCR/SRMF/SRMR/SMF/SMR/SPFR/SPFL

*1: for Automatic transmission

Freeze Frame Data

FREEZE FRAME DATA 1. FREEZE FRAME DATA HINT: Whenever a DTC is detected or the ABS operates, the skid control ECU stores the current vehicle (sensor) state as freeze frame data. The ...

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART NOTICE: When removing any parts, turn the ignition switch off. HINT: If no abnormality is found when inspecting parts, check the skid control ECU and chec ...

Other materials:

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals ...

Clutch Start Cancel Switch
Inspection INSPECTION PROCEDURE 1. INSPECT CLUTCH START CANCEL SWITCH ASSEMBLY (a) Using an ohmmeter, check that there is resistance between terminals 2 and 4. Standard: 10 kΩ or higher If the result is not as specified, replace the clutch start cancel switch. ...

Installation
INSTALLATION PROCEDURE 1. INSTALL TRANSMISSION WIRE (a) Coat 2 new O-rings with ATF, and install them to the 2 temperature sensors. (b) Coat a new O-ring with ATF, and install it to the transmission wire. (c) Install the transmission wire to the automatic transmission case sub-assembly with t ...