Toyota Tacoma (2015-2018) Service Manual: Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Body Electrical / Combination Meter / Data List.
(g) According to the display on the Techstream, read the Data List.
Combination Meter|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
ODO/TRIP Change SW |
ODO/TRIP switch/ OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
- |
||
|
Vehicle Speed Meter |
Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) |
Approximately same as actual vehicle speed (When vehicle is being driven) |
- |
|
Engine Rpm |
Engine speed/ Min.: 0 rpm, Max.: 12750 rpm |
600 to 700 rpm: Idling |
- |
|
Coolant Temperature |
Engine coolant temperature/ Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) |
80 to 100°C (176 to 212°F): After warming up |
- |
|
Washer Switch*1 |
Washer level warning switch/ OFF or ON |
OFF: Washer level warning switch off |
- |
|
ON: Washer level warning switch on |
|||
|
Oil Level SW |
Engine oil level warning/ OFF or ON |
OFF: Engine oil level warning not displayed to multi-information display |
- |
|
ON: Engine oil level warning displayed to multi-information display |
|||
|
Light Control Up Switch |
Light control rheostat up switch / OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Light Control Down Switch |
Light control rheostat down switch/ OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
+B Voltage Value |
Battery voltage/ Min.: 0 V, Max.: 25.5 V |
11 to 14 V |
- |
|
Integrated value for Maintenance*2 |
Maintenance required reminder value/ Min.: 0, Max.: 25500 (mile) |
Driving distance after performing maintenance required reminder reset procedure displayed |
If the value is 5000 (miles) or more, perform the maintenance required reminder reset procedure after performing maintenance. |
|
Fuel Input |
Fuel input signal/ Min.: 0, Max.: 127.5 |
Current fuel level displayed |
Unit: Liter |
|
Ambient Temperature |
Outside temperature/ Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) |
Almost the same as actual outside temperature |
The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F). |
|
Multi Switch (Up) |
Drive monitor switch (Up)/ OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Multi Switch (Down) |
Drive monitor switch (Down)/ OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Multi Switch (Menu) |
Steering pad switch (Menu)/ OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Multi Switch (Enter) |
Steering pad switch (Enter)/ OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Multi Switch (Right) |
Steering pad switch (Right)/ OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Multi Switch (Left) |
Steering pad switch (Left)/ OFF or ON |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Oil Pressure Switch |
Engine oil pressure switch/ OFF or ON |
OFF: Engine oil pressure low |
- |
|
ON: Engine oil pressure except above |
|||
|
Turn Signal Switch (Right) |
RH turn signal switch/ OFF or ON |
OFF: RH turn signal switch off |
- |
|
ON: RH turn signal switch on |
|||
|
Turn Signal Switch (Left) |
LH turn signal switch/ OFF or ON |
OFF: LH turn signal switch off |
- |
|
ON: LH turn signal switch on |
|||
|
Hazard Flasher Switch |
Hazard warning signal switch/ OFF or ON |
OFF: Hazard warning signal switch off |
- |
|
ON: Hazard warning signal switch on |
|||
|
Turn Switch Signal (Full Turn) |
Turn switch signal/ OFF or ON |
OFF: LH or RH turn switch off |
- |
|
ON: LH or RH turn switch on |
|||
|
Multi Switch (Back) |
Steering pad switch (Back)/ |
OFF: Switch released |
- |
|
ON: Switch pushed |
|||
|
Key Remind Sound*3 |
Cycle of key reminder warning buzzer/ Normal, Slow or Fast |
Cycle of key reminder warning buzzer is Fast, Normal or Slow |
The current setting of the cycle of the key reminder warning buzzer is displayed. |
|
Driver Side Seatbelt Warning Buzzer |
Condition of the driver side seat belt warning buzzer/ OFF or ON |
ON: Driver side seat belt warning buzzer sounds at a vehicle speed of 20 km/h (12 mph) or more when driver side seat belt unfastened |
The customized setting of the driver side seat belt warning buzzer is displayed. |
|
OFF: Driver side seat belt warning buzzer does not sound at a vehicle speed of 20 km/h (12 mph) or more when driver side seat belt unfastened |
|||
|
P-Seatbelt Warning Buzzer |
Condition of the front passenger side seat belt warning buzzer/ OFF or ON |
ON: Front passenger side seat belt warning buzzer sounds at a vehicle speed of 20 km/h (12 mph) or more when front passenger side seat belt unfastened and passenger occupant detected |
The customized setting of the front passenger side seat belt warning buzzer is displayed. |
|
OFF: Front passenger side seat belt warning buzzer does not sound at a vehicle speed of 20 km/h (12 mph) or more when front passenger side seat belt unfastened |
|||
|
ODO Display Time After IG OFF Setting |
Condition of the ODO display time after the ignition switch is turned off/ 30s, 60s, 600s or OFF |
Displays customize setting of ODO display time after IG off setting |
- |
|
Lane Change Flashing Times Setting |
Condition of the lane change flashing times OFF, 3, 4, 5, 6 or 7 |
Displays customize setting of lane change flashing times setting |
- |
|
TPMS System |
Existence of function/ With or Without |
With: w/ Tire pressure warning system Without: w/o Tire pressure warning system |
- |
|
LDA System |
Existence of function/ With or Without |
With: w/ Dynamic laser cruise control system Without: w/o Dynamic laser cruise control system |
- |
|
VSC System |
Existence of function/ With or Without |
With: w/ Vehicle stability control Without: w/o Vehicle stability control |
- |
|
PCS System |
Existence of function/ With or Without |
With: w/ Pre-collision System Without: w/o Pre-collision System |
- |
|
Intuitive P/A System |
With or Without |
With: w/ Intuitive Parking Assist System Without: w/o Intuitive Parking Assist System |
- |
|
Number of Trouble Code |
The number of the DTC which is currently output |
0 |
- |
- *1: w/ Washer Fluid Level Warning
- *2: w/ Maintenance Required Reminder
- *3: w/o Smart Key System
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(g) According to the display on the Techstream, perform the Active Test.
Combination Meter|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Speed Meter Operation |
Speedometer |
|
Operate with IG ON and the vehicle is stopped. |
|
There is a deviation in the values displayed on the speedometer (Control range → Speedometer display) Reference mph*1:
Reference km/h*2:
|
|||
|
TachoMeter Operation |
Tachometer |
OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 |
Operate with IG ON and the vehicle is stopped. |
|
Fuel Meter Operation |
Fuel receiver gauge |
OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F |
Operate with IG ON and the vehicle is stopped. |
|
A/T Indicator Operation 1 |
A/T shift indicator light (D, P, N. R, 4, 3, 2, L) |
OFF, L, 2, 3, 4, D, N, R, P |
Operate with IG ON and the vehicle is stopped. |
|
A/T Indicator Operation 2 |
A/T gear range indicator light (S, 8, 7, 6, 5) |
OFF, 8, 5, 6, 7, S |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp Airbag |
SRS warning light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Driver Side Seat Belt |
Driver side seat belt warning light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp ABS |
ABS warning light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp Slip |
Slip indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp Beam |
High beam indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp Head*1 |
Head indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp Tail*2 |
Tail indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp Fr FOG*3 |
Front fog indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Pre-Collision*4 |
PCS OFF warning light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp Fuel |
Fuel level warning light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Tire Pressure Warning System*5 |
Tire Pressure warning light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Lamp ECT PWR*6 |
ECT PWR indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped |
|
Indicat. Lamp Brake |
Brake warning light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Master Warning |
Master warning light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Auto LSD |
Slip indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Park |
Parking brake indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. Rr DIFF LOCK |
Rear differential lock indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. 4LO*7 |
Low speed four-wheel drive indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Indicat. VSC OFF |
VSC OFF indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Automatic High Beam Indicator*4 |
Automatic High Beam Indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Turn Signal (Left) Indicator |
LH turn indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Turn Signal (Right) Indicator |
RH turn indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
4WD Indicator (Green)*7 |
Four-wheel drive indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Check Engine Indicator |
Malfunction indicator light |
OFF or ON |
Operate with IG ON and the vehicle is stopped. |
|
Water Temperature Meter Operation |
Engine coolant temperature receiver gauge |
OFF, LOW, NORMAL, HIGH |
Operate with IG ON and the vehicle is stopped. |
|
Meter Display 1 |
Multi-information display |
OFF, 6, 5, 4, 3, 2, 1, 0, All |
Operate with IG ON and the vehicle is stopped. |
- *1: for Speedometer with Imperial Units for Main Scale
- *2: for Speedometer with Metric Units for Main Scale
- *3: w/ Fog Light
- *4: w/ Toyota Safety Sense P
- *5: w/ Tire Pressure Warning System
- *6: for Automatic Transmission
- *7: for 4WD
Terminals Of Ecu
TERMINALS OF ECU
1. COMBINATION METER ASSEMBLY
(a) Measure the voltage, resistance and check for pulses according to the value(s)
in the table below.
Terminal No. (Symbol)
...
Diagnosis System
DIAGNOSIS SYSTEM
1. CHECK DLC3
(a) Check the DLC3 (See page
).
2. INSPECT BATTERY VOLTAGE
(a) Measure the battery voltage.
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharg ...
Other materials:
Before Starting Adjustment
BEFORE STARTING ADJUSTMENT
CAUTION / NOTICE / HINT
NOTICE:
When replacing the windshield glass of a vehicle equipped with a forward recognition
camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is
used, the forward recognition camera may not be able to be installed ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
HINT:
If a trouble code is displayed during the DTC check, inspect the trouble areas
listed for that code. For details of the code, refer to the "See page" below.
Lighting system
DTC Code
Detection Item
See page
...
Yaw Rate Sensor Malfunction (C1436)
DESCRIPTION
The skid control ECU (brake actuator assembly) receives signals from the yaw
rate and acceleration sensor (airbag sensor assembly) via the CAN communication
system.
The airbag sensor assembly has a built-in yaw rate sensor and detects the vehicle
condition.
If there is trouble i ...
